SV-JME is indexed / abstracted in:

  • SCI-Expanded,
  • Compendex,
  • Inspec,
  • ProQuest-CSA,
  • SCOPUS,
  • TEMA, ...
The list of the remaining bases, in which SV-JME is indexed »

Founders and Publishers

University of Ljubljana, Faculty of Mechanical Engineering

University of Maribor, Faculty of Mechanical Engineering

 

Association of Mechanical Engineers of Slovenia

 

Chamber of Commerce and Industry Slovenia, Metal Processing Association

Editorial Office

University of Ljubljana
Faculty of Mechanical Engineering
Journal of Mechanical Engineering
Aškerčeva 6,

SI-1000 Ljubljana
Slovenia

P: +386 1 4771 137
E: info@sv-jme.eu


The magazine is subsidized by the Slovenian Research Agency (ARRS).

 

Current volume

   

SV - JME 56 (2010) 7-8

Table of contents

  1. Virtual User Interface for the Remote Control of a Nano-Robotic Cell Using a Haptic-Device
  2. Analysis of the Sailplane Final Approaches Performed by Cosine-Law Speed Variations
  3. An Investigation into the Influences of Grain Size and Grinding Parameters on Surface Roughness and Grinding Forces when Grinding
  4. Optimal Design of the Fuzzy Sliding Mode Control for a DC Servo Drive
  5. Flow Characteristics of Bladeless Impeller Made of Open Cell Porous Material
  6. Application of Group Technology in Complex Cluster Type Organizational Systems
  7. The Application of a New Formula of Nakaoka Coefficient in HF Inductive Welding
  8. Statistical Analysis for Strategic Innovation Decisions in Slovenian Mechanical Industry
  9. Characterization of the Dynamic Behaviour of a Basketball Goal Mounted on a Ceiling
  10. Analytical Description of Polygonal Holes Boring - General Approach
  11. The Role of the User and the Society in New Product Development
  12. Alternative to the Conventional Heating and Cooling Systems in Public Buildings

To journal contents >>
   

SV - JME 56 (2010) 6

Table of contents

  1. An Optimal Main Helicopter Rotor Projection Model Obtained by Viscous Effects and Unsteady Lift Simulation
  2. Analysis of Die Casting Tool Material
  3. Analysis of Ex-Vessel Steam Explosion Pressure Loads
  4. Application of Artificial Neural Networks in the Prediction of Critical Buckling Loads of Helical Compression Springs
  5. Simulation of Transient Flow in Hydroelectric Power Plants Using Unsteady Friction
  6. The Optimization of Machining Parameters Using the Taguchi Method For Surface Roughness of AISI 8660 Hardened Alloy Steel
  7. Conceptual Framework for NPN Logic Based Decision Analysis
  8. Methods of Shaping the Metrological Characteristics of Air Gages

To journal contents >>
   

SV - JME 56 (2010) 5

Table of contents

  1. Characterisation of High-Carbon Steel Surface Welded Layer
  2. Optimum Design of a Hybrid-driven Mechanical Press Based on Inverse Kinematics
  3. Application of Non-Discrete Boundaries with Friction to Smoothed Particle Hydrodynamics
  4. Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method
  5. A Multi-Objective optimization of a robotic arm for service tasks
  6. Solving JSSP by Introducing Hamilton Similarity and Time Dependent Fitness Scaling
  7. Novel Technique for Spatial Objects Shaping With High-Pressure Abrasive Water Jet

To journal contents >>
   

SV - JME 56 (2010) 4

Table of contents

  1. A Model for Scuffing Prediction
  2. Logarithmical Crowning for Spur Gears
  3. Influence of the Oil Churning, the Bearing and the Tooth Friction Losses on the Efficiency of Planetary Gears
  4. EHL-Squeeze in High Loaded Contacts: The Case of Chain CVT Transmissions
  5. Static Behaviour of Air Plane Pads: Comparison Between Different Feeding Solutions
  6. Influence of Heat Treatment and Machining Parameters on Residual Stress Field and Wear of Double-Layer Cast Rolls
  7. Impact of Solid Particulate on Brittle Materials
  8. Wear Particle Classifier System Based On An Artificial Neural Network

To journal contents >>
   

SV - JME 56 (2010) 3

Table of contents

  1. Practical Tracking Control of the Electropneumatic Piston Drive
  2. Feature Models in Virtual Product Development
  3. The Possibility for FMEA Method Improvement and its Implementation into Bus Life Cycle
  4. Calculations of the Unloading Operation in Case of Liquid Cargo Service With High Density on Modern Product and Chemical Tankers Equipped With Hydraulic Submerged Cargo Pumps
  5. An Experimental Investigation on Effect of Cutting Fluids in Turning with Coated Carbides Tool
  6. Machining of titanium alloy Ti-6Al-4V for biomedical applications
  7. Practical Implementation of Load Sharing and Anti Skew Controllers for Wide Span Gantry Crane Drives
  8. Integration of information for manufacturing shop control

To journal contents >>
   

SV - JME 56 (2010) 2

Table of contents

  1. Evaluation Of Hardening Performance of Cooling Media by Using Inverse Heat Conduction Methods and Property Prediction
  2. Extension of Isothermal Time-Temperature Parameters to Non-isothermal Conditions: Application to the Simulation of Rapid Tempering
  3. A Simulation of the Quenching Process for Predicting Temperature, Microstructure and Residual Stresses
  4. Prediction of Quench-Hardness within the Whole Volume of Axially-Symmetric Workpieces of any Shape
  5. Predictions of Mechanical Properties of Quenched and Tempered Steel
  6. Effect of Antioxidants and Corrosion Inhibitor Additives on the Quenching Performance of Soybean Oil

  7. Vegetable Oil Quenchants: Calculation and Comparison of The Cooling Properties of a Series of Vegetable Oils
  8. The Effect of Heat Treatment on the Stability of Centerline Segregation
  9. Influence of the Graphite Absorber During Laser Surface Hardening

To journal contents >>
   

SV - JME 56 (2010)1

Table of contents

  1. Countrywide Positioning of Domestic Solar Water Heating Systems using Risk Analysis and GIS
  2. Effectivity of Hypergeometric Function Application in Numerical Simulation of Helicopter Rotor Blades Theory
  3. The Influence of Surface Topology on the Accuracy of Laser Triangulation Scanning Results
  4. Muscular-Skeletal Diseases Require Scientifically Designed Sewing Workstations
  5. Risk Analysis Methodology for Road Tunnels and Alternative Routes

  6. Modelling Metal cutting Parameters Using Intelligent Techniques

  7. A Multi-Criteria Assessment of Energy Crops for Biogas Production

To journal contents >>
   

Journal of Mechanical Engineering

in digital form



SV-JME-6-2010» SV-JME-5-2010» SV-JME-4-2010» SV-JME-3-2010»  

 

 


Sign up for the FREE SV-JME Newsletter

Enter your email address below to receive your newsletter subscriptions.
Name and surname:

E-mail:
Subscribe
Unsubscribe