An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds

1838 Ogledov
1630 Prenosov
Izvoz citacije: ABNT
DILIPAK, Hakan ;GÜLDAŞ, Abdulmecit ;GEZGIN, Akin .
An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds. 
Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 55, n.7-8, p. 438-443, august 2017. 
ISSN 0039-2480.
Available at: <https://www.sv-jme.eu/sl/article/an-investigation-of-the-number-of-inserts-effect-on-the-machining-time-and-metal-removal-rate-during-the-milling-of-aisi-d3-steel-at-high-cutting-speeds/>. Date accessed: 10 nov. 2024. 
doi:http://dx.doi.org/.
Dilipak, H., Güldaş, A., & Gezgin, A.
(2009).
An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds.
Strojniški vestnik - Journal of Mechanical Engineering, 55(7-8), 438-443.
doi:http://dx.doi.org/
@article{.,
	author = {Hakan  Dilipak and Abdulmecit  Güldaş and Akin  Gezgin},
	title = {An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {55},
	number = {7-8},
	year = {2009},
	keywords = {machining time; flank wear; metal removal rate in milling; },
	abstract = {In this study, the effect of the number of milling cutter inserts on the metal removal and the machining time in milling of AISI D3 cold work tool steel has been investigated. A CNC machining centre was used for cutting operations. The machinability tests were carried out in dry cutting conditions at various cutting speeds, feed rates and with different number of inserts. The flank wear was measured by using an optical microscope in order to determine the tool life. The machining time decreased when the cutting speed, the number of inserts and feed rate increased. On the contrary, the flank wear increased when the same parameters increased. The flank wear increased gradually until the first 0.2 mm, but the wear rate increased significantly when above this point under different cutting conditions and with different numbers of inserts. This condition following the first 0.2 mm wear value was constant due to the high cutting speed rates based on the notch wear which emerged from fast wear.},
	issn = {0039-2480},	pages = {438-443},	doi = {},
	url = {https://www.sv-jme.eu/sl/article/an-investigation-of-the-number-of-inserts-effect-on-the-machining-time-and-metal-removal-rate-during-the-milling-of-aisi-d3-steel-at-high-cutting-speeds/}
}
Dilipak, H.,Güldaş, A.,Gezgin, A.
2009 August 55. An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 55:7-8
%A Dilipak, Hakan 
%A Güldaş, Abdulmecit 
%A Gezgin, Akin 
%D 2009
%T An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds
%B 2009
%9 machining time; flank wear; metal removal rate in milling; 
%! An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds
%K machining time; flank wear; metal removal rate in milling; 
%X In this study, the effect of the number of milling cutter inserts on the metal removal and the machining time in milling of AISI D3 cold work tool steel has been investigated. A CNC machining centre was used for cutting operations. The machinability tests were carried out in dry cutting conditions at various cutting speeds, feed rates and with different number of inserts. The flank wear was measured by using an optical microscope in order to determine the tool life. The machining time decreased when the cutting speed, the number of inserts and feed rate increased. On the contrary, the flank wear increased when the same parameters increased. The flank wear increased gradually until the first 0.2 mm, but the wear rate increased significantly when above this point under different cutting conditions and with different numbers of inserts. This condition following the first 0.2 mm wear value was constant due to the high cutting speed rates based on the notch wear which emerged from fast wear.
%U https://www.sv-jme.eu/sl/article/an-investigation-of-the-number-of-inserts-effect-on-the-machining-time-and-metal-removal-rate-during-the-milling-of-aisi-d3-steel-at-high-cutting-speeds/
%0 Journal Article
%R 
%& 438
%P 6
%J Strojniški vestnik - Journal of Mechanical Engineering
%V 55
%N 7-8
%@ 0039-2480
%8 2017-08-21
%7 2017-08-21
Dilipak, Hakan, Abdulmecit  Güldaş, & Akin  Gezgin.
"An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds." Strojniški vestnik - Journal of Mechanical Engineering [Online], 55.7-8 (2009): 438-443. Web.  10 Nov. 2024
TY  - JOUR
AU  - Dilipak, Hakan 
AU  - Güldaş, Abdulmecit 
AU  - Gezgin, Akin 
PY  - 2009
TI  - An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds
JF  - Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - machining time; flank wear; metal removal rate in milling; 
N2  - In this study, the effect of the number of milling cutter inserts on the metal removal and the machining time in milling of AISI D3 cold work tool steel has been investigated. A CNC machining centre was used for cutting operations. The machinability tests were carried out in dry cutting conditions at various cutting speeds, feed rates and with different number of inserts. The flank wear was measured by using an optical microscope in order to determine the tool life. The machining time decreased when the cutting speed, the number of inserts and feed rate increased. On the contrary, the flank wear increased when the same parameters increased. The flank wear increased gradually until the first 0.2 mm, but the wear rate increased significantly when above this point under different cutting conditions and with different numbers of inserts. This condition following the first 0.2 mm wear value was constant due to the high cutting speed rates based on the notch wear which emerged from fast wear.
UR  - https://www.sv-jme.eu/sl/article/an-investigation-of-the-number-of-inserts-effect-on-the-machining-time-and-metal-removal-rate-during-the-milling-of-aisi-d3-steel-at-high-cutting-speeds/
@article{{}{.},
	author = {Dilipak, H., Güldaş, A., Gezgin, A.},
	title = {An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {55},
	number = {7-8},
	year = {2009},
	doi = {},
	url = {https://www.sv-jme.eu/sl/article/an-investigation-of-the-number-of-inserts-effect-on-the-machining-time-and-metal-removal-rate-during-the-milling-of-aisi-d3-steel-at-high-cutting-speeds/}
}
TY  - JOUR
AU  - Dilipak, Hakan 
AU  - Güldaş, Abdulmecit 
AU  - Gezgin, Akin 
PY  - 2017/08/21
TI  - An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds
JF  - Strojniški vestnik - Journal of Mechanical Engineering; Vol 55, No 7-8 (2009): Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - machining time, flank wear, metal removal rate in milling, 
N2  - In this study, the effect of the number of milling cutter inserts on the metal removal and the machining time in milling of AISI D3 cold work tool steel has been investigated. A CNC machining centre was used for cutting operations. The machinability tests were carried out in dry cutting conditions at various cutting speeds, feed rates and with different number of inserts. The flank wear was measured by using an optical microscope in order to determine the tool life. The machining time decreased when the cutting speed, the number of inserts and feed rate increased. On the contrary, the flank wear increased when the same parameters increased. The flank wear increased gradually until the first 0.2 mm, but the wear rate increased significantly when above this point under different cutting conditions and with different numbers of inserts. This condition following the first 0.2 mm wear value was constant due to the high cutting speed rates based on the notch wear which emerged from fast wear.
UR  - https://www.sv-jme.eu/sl/article/an-investigation-of-the-number-of-inserts-effect-on-the-machining-time-and-metal-removal-rate-during-the-milling-of-aisi-d3-steel-at-high-cutting-speeds/
Dilipak, Hakan, Güldaş, Abdulmecit, AND Gezgin, Akin.
"An Investigation of the Number of Inserts Effect on the Machining Time and Metal Removal Rate During the Milling of AISI D3 Steel at High Cutting Speeds" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 55 Number 7-8 (21 August 2017)

Avtorji

Inštitucije

  • Department of Mechanical Education, Technical Education Faculty, Gazi University, Turkey
  • Department of Mechanical Education, Technical Education Faculty, Gazi University, Turkey
  • Mechanical Education, Institute of Science & Technology, Gazi University, Maltepe, Turkey

Informacije o papirju

Strojniški vestnik - Journal of Mechanical Engineering 55(2009)7-8, 438-443
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.

In this study, the effect of the number of milling cutter inserts on the metal removal and the machining time in milling of AISI D3 cold work tool steel has been investigated. A CNC machining centre was used for cutting operations. The machinability tests were carried out in dry cutting conditions at various cutting speeds, feed rates and with different number of inserts. The flank wear was measured by using an optical microscope in order to determine the tool life. The machining time decreased when the cutting speed, the number of inserts and feed rate increased. On the contrary, the flank wear increased when the same parameters increased. The flank wear increased gradually until the first 0.2 mm, but the wear rate increased significantly when above this point under different cutting conditions and with different numbers of inserts. This condition following the first 0.2 mm wear value was constant due to the high cutting speed rates based on the notch wear which emerged from fast wear.

machining time; flank wear; metal removal rate in milling;