Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations

1870 Ogledov
1417 Prenosov
Izvoz citacije: ABNT
PODGORNIK, Bojan ;VIŽINTIN, Jože .
Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations. 
Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 49, n.4, p. 242-249, july 2017. 
ISSN 0039-2480.
Available at: <https://www.sv-jme.eu/sl/article/hard-pvd-coatings-in-mechanical-engineering-perspectives-and-limitations/>. Date accessed: 15 oct. 2024. 
doi:http://dx.doi.org/.
Podgornik, B., & Vižintin, J.
(2003).
Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations.
Strojniški vestnik - Journal of Mechanical Engineering, 49(4), 242-249.
doi:http://dx.doi.org/
@article{.,
	author = {Bojan  Podgornik and Jože  Vižintin},
	title = {Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {49},
	number = {4},
	year = {2003},
	keywords = {hard coatings; friction; wear; plasma nitriding; },
	abstract = {A lot of new technologies, and thin films with very good tribological properties, like diamond and diamond-like carbon coatings, were introduced in the past 2 to 3 decades. However, the use of hard, thin films in the field of machine elements is the exception rather than the rule. The main problem lies in the relatively high contact pressure and the very complex loading of the machine components, which demand a hard resistant surface and a tough core. It was found during many numerical and experimental analyses that in the case of hard, thin films the plastic deformation of the composite starts in the substrate. Therefore, the ability of the film to sustain the loading depends principally on the load-carrying capacity of the substrate. Although there are an almost unlimited number of possibilities, we have to be very careful when combining different surface treatments and thin-film deposition techniques. It should be pointed out that the wrong combination can very easily lead to an undesirable deterioration of the properties, either of the film or the substrate, instead of an improvement. This is why only a few combinations can be successfully used in practice. One of the most promising ones, already proven in the case of high-speed steel, is the combination of plasma nitriding of a steel substrate followed by PVD (physical vapour deposition) thin-film deposition.},
	issn = {0039-2480},	pages = {242-249},	doi = {},
	url = {https://www.sv-jme.eu/sl/article/hard-pvd-coatings-in-mechanical-engineering-perspectives-and-limitations/}
}
Podgornik, B.,Vižintin, J.
2003 July 49. Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 49:4
%A Podgornik, Bojan 
%A Vižintin, Jože 
%D 2003
%T Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations
%B 2003
%9 hard coatings; friction; wear; plasma nitriding; 
%! Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations
%K hard coatings; friction; wear; plasma nitriding; 
%X A lot of new technologies, and thin films with very good tribological properties, like diamond and diamond-like carbon coatings, were introduced in the past 2 to 3 decades. However, the use of hard, thin films in the field of machine elements is the exception rather than the rule. The main problem lies in the relatively high contact pressure and the very complex loading of the machine components, which demand a hard resistant surface and a tough core. It was found during many numerical and experimental analyses that in the case of hard, thin films the plastic deformation of the composite starts in the substrate. Therefore, the ability of the film to sustain the loading depends principally on the load-carrying capacity of the substrate. Although there are an almost unlimited number of possibilities, we have to be very careful when combining different surface treatments and thin-film deposition techniques. It should be pointed out that the wrong combination can very easily lead to an undesirable deterioration of the properties, either of the film or the substrate, instead of an improvement. This is why only a few combinations can be successfully used in practice. One of the most promising ones, already proven in the case of high-speed steel, is the combination of plasma nitriding of a steel substrate followed by PVD (physical vapour deposition) thin-film deposition.
%U https://www.sv-jme.eu/sl/article/hard-pvd-coatings-in-mechanical-engineering-perspectives-and-limitations/
%0 Journal Article
%R 
%& 242
%P 8
%J Strojniški vestnik - Journal of Mechanical Engineering
%V 49
%N 4
%@ 0039-2480
%8 2017-07-07
%7 2017-07-07
Podgornik, Bojan, & Jože  Vižintin.
"Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations." Strojniški vestnik - Journal of Mechanical Engineering [Online], 49.4 (2003): 242-249. Web.  15 Oct. 2024
TY  - JOUR
AU  - Podgornik, Bojan 
AU  - Vižintin, Jože 
PY  - 2003
TI  - Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations
JF  - Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - hard coatings; friction; wear; plasma nitriding; 
N2  - A lot of new technologies, and thin films with very good tribological properties, like diamond and diamond-like carbon coatings, were introduced in the past 2 to 3 decades. However, the use of hard, thin films in the field of machine elements is the exception rather than the rule. The main problem lies in the relatively high contact pressure and the very complex loading of the machine components, which demand a hard resistant surface and a tough core. It was found during many numerical and experimental analyses that in the case of hard, thin films the plastic deformation of the composite starts in the substrate. Therefore, the ability of the film to sustain the loading depends principally on the load-carrying capacity of the substrate. Although there are an almost unlimited number of possibilities, we have to be very careful when combining different surface treatments and thin-film deposition techniques. It should be pointed out that the wrong combination can very easily lead to an undesirable deterioration of the properties, either of the film or the substrate, instead of an improvement. This is why only a few combinations can be successfully used in practice. One of the most promising ones, already proven in the case of high-speed steel, is the combination of plasma nitriding of a steel substrate followed by PVD (physical vapour deposition) thin-film deposition.
UR  - https://www.sv-jme.eu/sl/article/hard-pvd-coatings-in-mechanical-engineering-perspectives-and-limitations/
@article{{}{.},
	author = {Podgornik, B., Vižintin, J.},
	title = {Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {49},
	number = {4},
	year = {2003},
	doi = {},
	url = {https://www.sv-jme.eu/sl/article/hard-pvd-coatings-in-mechanical-engineering-perspectives-and-limitations/}
}
TY  - JOUR
AU  - Podgornik, Bojan 
AU  - Vižintin, Jože 
PY  - 2017/07/07
TI  - Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations
JF  - Strojniški vestnik - Journal of Mechanical Engineering; Vol 49, No 4 (2003): Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - hard coatings, friction, wear, plasma nitriding, 
N2  - A lot of new technologies, and thin films with very good tribological properties, like diamond and diamond-like carbon coatings, were introduced in the past 2 to 3 decades. However, the use of hard, thin films in the field of machine elements is the exception rather than the rule. The main problem lies in the relatively high contact pressure and the very complex loading of the machine components, which demand a hard resistant surface and a tough core. It was found during many numerical and experimental analyses that in the case of hard, thin films the plastic deformation of the composite starts in the substrate. Therefore, the ability of the film to sustain the loading depends principally on the load-carrying capacity of the substrate. Although there are an almost unlimited number of possibilities, we have to be very careful when combining different surface treatments and thin-film deposition techniques. It should be pointed out that the wrong combination can very easily lead to an undesirable deterioration of the properties, either of the film or the substrate, instead of an improvement. This is why only a few combinations can be successfully used in practice. One of the most promising ones, already proven in the case of high-speed steel, is the combination of plasma nitriding of a steel substrate followed by PVD (physical vapour deposition) thin-film deposition.
UR  - https://www.sv-jme.eu/sl/article/hard-pvd-coatings-in-mechanical-engineering-perspectives-and-limitations/
Podgornik, Bojan, AND Vižintin, Jože.
"Hard PVD Coatings in Mechanical Engineering – Perspectives and Limitations" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 49 Number 4 (07 July 2017)

Avtorji

Inštitucije

  • University of Ljubljana, Faculty of Mechanical Engineering, Slovenia
  • University of Ljubljana, Faculty of Mechanical Engineering, Slovenia

Informacije o papirju

Strojniški vestnik - Journal of Mechanical Engineering 49(2003)4, 242-249
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.

A lot of new technologies, and thin films with very good tribological properties, like diamond and diamond-like carbon coatings, were introduced in the past 2 to 3 decades. However, the use of hard, thin films in the field of machine elements is the exception rather than the rule. The main problem lies in the relatively high contact pressure and the very complex loading of the machine components, which demand a hard resistant surface and a tough core. It was found during many numerical and experimental analyses that in the case of hard, thin films the plastic deformation of the composite starts in the substrate. Therefore, the ability of the film to sustain the loading depends principally on the load-carrying capacity of the substrate. Although there are an almost unlimited number of possibilities, we have to be very careful when combining different surface treatments and thin-film deposition techniques. It should be pointed out that the wrong combination can very easily lead to an undesirable deterioration of the properties, either of the film or the substrate, instead of an improvement. This is why only a few combinations can be successfully used in practice. One of the most promising ones, already proven in the case of high-speed steel, is the combination of plasma nitriding of a steel substrate followed by PVD (physical vapour deposition) thin-film deposition.

hard coatings; friction; wear; plasma nitriding;