RUDONJA, Nedžad ;ZLATANOVI´C, Ivan ;BANJAC, Miloš ;GOJAK, Milan ;TODOROVIĆ, Ružica . Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia. Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 71, n.7-8, p. 242-248, july 2025. ISSN 0039-2480. Available at: <https://www.sv-jme.eu/article/thermodynamic-evaluation-and-working-fluid-selection-for-a-heat-pump-integrated-into-a-hydropower-plant-hvac-system-a-case-study-from-serbia/>. Date accessed: 10 sep. 2025. doi:http://dx.doi.org/10.5545/sv-jme.2025.1344.
Rudonja, N., Zlatanovi´c, I., Banjac, M., Gojak, M., & Todorović, R. (2025). Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia. Strojniški vestnik - Journal of Mechanical Engineering, 71(7-8), 242-248. doi:http://dx.doi.org/10.5545/sv-jme.2025.1344
@article{sv-jmesv-jme.2025.1344,
author = {Nedžad Rudonja and Ivan Zlatanovi´c and Miloš Banjac and Milan Gojak and Ružica Todorović},
title = {Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia},
journal = {Strojniški vestnik - Journal of Mechanical Engineering},
volume = {71},
number = {7-8},
year = {2025},
keywords = {hydropower plant; heat pump; energy efficiency; COP; SCOP; },
abstract = {This paper presents a thermodynamic analysis of two types of heat pumps integrated into the heating, ventilation, and air conditioning (HVAC) system of the “Bajina Bašta” hydropower plant located in Serbia. The study aims to replace existing electric boilers with more energy-efficient solutions by utilising renewable heat sources. A comparative evaluation of water source heat pump (WSHP) and air source heat pump (ASHP) configurations was conducted using a custom-developed MATLAB model based on CoolProp data of working fluids. The analysis was supported by real data obtained through in situ measurements of air and water temperatures at the selected location, ensuring accurate input parameters for the simulations. Five refrigerants (R-410A, R-407C, R-134a, R-32, and R-1270) were used, and R-32 was selected as the optimal working fluid because of its high efficiency, moderate flammability, and low environmental impact. The lowest coefficient of performance (COP) for the WSHP was 3.27 in January, while the seasonal coefficient of performance (SCOP) reached 3.36, approximately 15.5 % higher than the ASHP counterpart (SCOP = 2.91). The study confirms that, upon analyzing the entire heating period, WSHP systems are technically and environmentally superior to ASHPs in the locations studied. The proposed configuration, based on real measured data and obtained results, can significantly improve energy efficiency and reduce internal electricity consumption in hydropower plants, thereby supporting the decarbonisation of large-scale renewable energy facilities. While most previous studies have focused on improving energy efficiency in buildings, this work demonstrates the substantial yet underexplored potential for efficiency improvements in the electricity production sector in Serbia. The study specifically examines hydropower plants in Serbia, where heating and air conditioning systems built in the 1960s remain highly energy inefficient. By quantifying the benefits of integrating WSHP and ASHP systems, the research highlights a pathway toward significantly enhancing the energy efficiency of hydropower infrastructures.},
issn = {0039-2480}, pages = {242-248}, doi = {10.5545/sv-jme.2025.1344},
url = {https://www.sv-jme.eu/article/thermodynamic-evaluation-and-working-fluid-selection-for-a-heat-pump-integrated-into-a-hydropower-plant-hvac-system-a-case-study-from-serbia/}
}
Rudonja, N.,Zlatanovi´c, I.,Banjac, M.,Gojak, M.,Todorović, R. 2025 July 71. Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 71:7-8
%A Rudonja, Nedžad %A Zlatanovi´c, Ivan %A Banjac, Miloš %A Gojak, Milan %A Todorović, Ružica %D 2025 %T Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia %B 2025 %9 hydropower plant; heat pump; energy efficiency; COP; SCOP; %! Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia %K hydropower plant; heat pump; energy efficiency; COP; SCOP; %X This paper presents a thermodynamic analysis of two types of heat pumps integrated into the heating, ventilation, and air conditioning (HVAC) system of the “Bajina Bašta” hydropower plant located in Serbia. The study aims to replace existing electric boilers with more energy-efficient solutions by utilising renewable heat sources. A comparative evaluation of water source heat pump (WSHP) and air source heat pump (ASHP) configurations was conducted using a custom-developed MATLAB model based on CoolProp data of working fluids. The analysis was supported by real data obtained through in situ measurements of air and water temperatures at the selected location, ensuring accurate input parameters for the simulations. Five refrigerants (R-410A, R-407C, R-134a, R-32, and R-1270) were used, and R-32 was selected as the optimal working fluid because of its high efficiency, moderate flammability, and low environmental impact. The lowest coefficient of performance (COP) for the WSHP was 3.27 in January, while the seasonal coefficient of performance (SCOP) reached 3.36, approximately 15.5 % higher than the ASHP counterpart (SCOP = 2.91). The study confirms that, upon analyzing the entire heating period, WSHP systems are technically and environmentally superior to ASHPs in the locations studied. The proposed configuration, based on real measured data and obtained results, can significantly improve energy efficiency and reduce internal electricity consumption in hydropower plants, thereby supporting the decarbonisation of large-scale renewable energy facilities. While most previous studies have focused on improving energy efficiency in buildings, this work demonstrates the substantial yet underexplored potential for efficiency improvements in the electricity production sector in Serbia. The study specifically examines hydropower plants in Serbia, where heating and air conditioning systems built in the 1960s remain highly energy inefficient. By quantifying the benefits of integrating WSHP and ASHP systems, the research highlights a pathway toward significantly enhancing the energy efficiency of hydropower infrastructures. %U https://www.sv-jme.eu/article/thermodynamic-evaluation-and-working-fluid-selection-for-a-heat-pump-integrated-into-a-hydropower-plant-hvac-system-a-case-study-from-serbia/ %0 Journal Article %R 10.5545/sv-jme.2025.1344 %& 242 %P 7 %J Strojniški vestnik - Journal of Mechanical Engineering %V 71 %N 7-8 %@ 0039-2480 %8 2025-07-09 %7 2025-07-09
Rudonja, Nedžad, Ivan Zlatanovi´c, Miloš Banjac, Milan Gojak, & Ružica Todorović. "Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia." Strojniški vestnik - Journal of Mechanical Engineering [Online], 71.7-8 (2025): 242-248. Web. 10 Sep. 2025
TY - JOUR AU - Rudonja, Nedžad AU - Zlatanovi´c, Ivan AU - Banjac, Miloš AU - Gojak, Milan AU - Todorović, Ružica PY - 2025 TI - Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia JF - Strojniški vestnik - Journal of Mechanical Engineering DO - 10.5545/sv-jme.2025.1344 KW - hydropower plant; heat pump; energy efficiency; COP; SCOP; N2 - This paper presents a thermodynamic analysis of two types of heat pumps integrated into the heating, ventilation, and air conditioning (HVAC) system of the “Bajina Bašta” hydropower plant located in Serbia. The study aims to replace existing electric boilers with more energy-efficient solutions by utilising renewable heat sources. A comparative evaluation of water source heat pump (WSHP) and air source heat pump (ASHP) configurations was conducted using a custom-developed MATLAB model based on CoolProp data of working fluids. The analysis was supported by real data obtained through in situ measurements of air and water temperatures at the selected location, ensuring accurate input parameters for the simulations. Five refrigerants (R-410A, R-407C, R-134a, R-32, and R-1270) were used, and R-32 was selected as the optimal working fluid because of its high efficiency, moderate flammability, and low environmental impact. The lowest coefficient of performance (COP) for the WSHP was 3.27 in January, while the seasonal coefficient of performance (SCOP) reached 3.36, approximately 15.5 % higher than the ASHP counterpart (SCOP = 2.91). The study confirms that, upon analyzing the entire heating period, WSHP systems are technically and environmentally superior to ASHPs in the locations studied. The proposed configuration, based on real measured data and obtained results, can significantly improve energy efficiency and reduce internal electricity consumption in hydropower plants, thereby supporting the decarbonisation of large-scale renewable energy facilities. While most previous studies have focused on improving energy efficiency in buildings, this work demonstrates the substantial yet underexplored potential for efficiency improvements in the electricity production sector in Serbia. The study specifically examines hydropower plants in Serbia, where heating and air conditioning systems built in the 1960s remain highly energy inefficient. By quantifying the benefits of integrating WSHP and ASHP systems, the research highlights a pathway toward significantly enhancing the energy efficiency of hydropower infrastructures. UR - https://www.sv-jme.eu/article/thermodynamic-evaluation-and-working-fluid-selection-for-a-heat-pump-integrated-into-a-hydropower-plant-hvac-system-a-case-study-from-serbia/
@article{{sv-jme}{sv-jme.2025.1344},
author = {Rudonja, N., Zlatanovi´c, I., Banjac, M., Gojak, M., Todorović, R.},
title = {Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia},
journal = {Strojniški vestnik - Journal of Mechanical Engineering},
volume = {71},
number = {7-8},
year = {2025},
doi = {10.5545/sv-jme.2025.1344},
url = {https://www.sv-jme.eu/article/thermodynamic-evaluation-and-working-fluid-selection-for-a-heat-pump-integrated-into-a-hydropower-plant-hvac-system-a-case-study-from-serbia/}
}
TY - JOUR AU - Rudonja, Nedžad AU - Zlatanovi´c, Ivan AU - Banjac, Miloš AU - Gojak, Milan AU - Todorović, Ružica PY - 2025/07/09 TI - Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia JF - Strojniški vestnik - Journal of Mechanical Engineering; Vol 71, No 7-8 (2025): Strojniški vestnik - Journal of Mechanical Engineering DO - 10.5545/sv-jme.2025.1344 KW - hydropower plant, heat pump, energy efficiency, COP, SCOP, N2 - This paper presents a thermodynamic analysis of two types of heat pumps integrated into the heating, ventilation, and air conditioning (HVAC) system of the “Bajina Bašta” hydropower plant located in Serbia. The study aims to replace existing electric boilers with more energy-efficient solutions by utilising renewable heat sources. A comparative evaluation of water source heat pump (WSHP) and air source heat pump (ASHP) configurations was conducted using a custom-developed MATLAB model based on CoolProp data of working fluids. The analysis was supported by real data obtained through in situ measurements of air and water temperatures at the selected location, ensuring accurate input parameters for the simulations. Five refrigerants (R-410A, R-407C, R-134a, R-32, and R-1270) were used, and R-32 was selected as the optimal working fluid because of its high efficiency, moderate flammability, and low environmental impact. The lowest coefficient of performance (COP) for the WSHP was 3.27 in January, while the seasonal coefficient of performance (SCOP) reached 3.36, approximately 15.5 % higher than the ASHP counterpart (SCOP = 2.91). The study confirms that, upon analyzing the entire heating period, WSHP systems are technically and environmentally superior to ASHPs in the locations studied. The proposed configuration, based on real measured data and obtained results, can significantly improve energy efficiency and reduce internal electricity consumption in hydropower plants, thereby supporting the decarbonisation of large-scale renewable energy facilities. While most previous studies have focused on improving energy efficiency in buildings, this work demonstrates the substantial yet underexplored potential for efficiency improvements in the electricity production sector in Serbia. The study specifically examines hydropower plants in Serbia, where heating and air conditioning systems built in the 1960s remain highly energy inefficient. By quantifying the benefits of integrating WSHP and ASHP systems, the research highlights a pathway toward significantly enhancing the energy efficiency of hydropower infrastructures. UR - https://www.sv-jme.eu/article/thermodynamic-evaluation-and-working-fluid-selection-for-a-heat-pump-integrated-into-a-hydropower-plant-hvac-system-a-case-study-from-serbia/
Rudonja, Nedžad, Zlatanovi´c, Ivan, Banjac, Miloš, Gojak, Milan, AND Todorović, Ružica. "Thermodynamic Evaluation and Working Fluid Selection for a Heat Pump Integrated into a Hydropower Plant HVAC System: A Case Study from Serbia" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 71 Number 7-8 (09 July 2025)
Strojniški vestnik - Journal of Mechanical Engineering 71(2025)7-8, 242-248
© The Authors 2025. CC BY 4.0 Int.
This paper presents a thermodynamic analysis of two types of heat pumps integrated into the heating, ventilation, and air conditioning (HVAC) system of the “Bajina Bašta” hydropower plant located in Serbia. The study aims to replace existing electric boilers with more energy-efficient solutions by utilising renewable heat sources. A comparative evaluation of water source heat pump (WSHP) and air source heat pump (ASHP) configurations was conducted using a custom-developed MATLAB model based on CoolProp data of working fluids. The analysis was supported by real data obtained through in situ measurements of air and water temperatures at the selected location, ensuring accurate input parameters for the simulations. Five refrigerants (R-410A, R-407C, R-134a, R-32, and R-1270) were used, and R-32 was selected as the optimal working fluid because of its high efficiency, moderate flammability, and low environmental impact. The lowest coefficient of performance (COP) for the WSHP was 3.27 in January, while the seasonal coefficient of performance (SCOP) reached 3.36, approximately 15.5 % higher than the ASHP counterpart (SCOP = 2.91). The study confirms that, upon analyzing the entire heating period, WSHP systems are technically and environmentally superior to ASHPs in the locations studied. The proposed configuration, based on real measured data and obtained results, can significantly improve energy efficiency and reduce internal electricity consumption in hydropower plants, thereby supporting the decarbonisation of large-scale renewable energy facilities. While most previous studies have focused on improving energy efficiency in buildings, this work demonstrates the substantial yet underexplored potential for efficiency improvements in the electricity production sector in Serbia. The study specifically examines hydropower plants in Serbia, where heating and air conditioning systems built in the 1960s remain highly energy inefficient. By quantifying the benefits of integrating WSHP and ASHP systems, the research highlights a pathway toward significantly enhancing the energy efficiency of hydropower infrastructures.