A model-based system for the dynamic adjustment of cutting parameters during a milling process

1244 Views
911 Downloads
Export citation: ABNT
ČUŠ, Franci ;ŽUPERL, Uroš ;KIKER, Edvard .
A model-based system for the dynamic adjustment of cutting parameters during a milling process. 
Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 53, n.9, p. 524-540, august 2017. 
ISSN 0039-2480.
Available at: <https://www.sv-jme.eu/article/a-model-based-system-for-the-dynamic-adjustment-of-cutting-parameters-during-a-milling-process/>. Date accessed: 04 jul. 2022. 
doi:http://dx.doi.org/.
Čuš, F., Župerl, U., & Kiker, E.
(2007).
A model-based system for the dynamic adjustment of cutting parameters during a milling process.
Strojniški vestnik - Journal of Mechanical Engineering, 53(9), 524-540.
doi:http://dx.doi.org/
@article{.,
	author = {Franci  Čuš and Uroš  Župerl and Edvard  Kiker},
	title = {A model-based system for the dynamic adjustment of cutting parameters during a milling process},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {53},
	number = {9},
	year = {2007},
	keywords = {end-milling; cutting parameters; genetic programming; model-based control; },
	abstract = {This paper presents a model-based mechanism of control ensuring the constant quality of the surface finish by controlling the cutting forces during the end-milling process. Using the dynamic adaptation of feeding and speed the system controls the surface roughness and the cutting forces on the milling cutter The purpose of developing such a mechanism is to find the limitations of this type of control, which maintains a constant cutting force by adapting the cutting parameters. This model-based system of control was developed by the evolutionary method of genetic programming (GP). A drawing of experiments was made in order to determine the empirical correlations between the quality of the surface finish and the cutting force. With the depth of cutting defined in advance the influence of the workpiece material and cutting parameters (feeding, cutting depth) on the above mentioned correlation has been experimentally researched. The evolution genetic programming method (GP) was applied to derive an empirical relationship for the surface finish and the cutting force values for steel materials. These relationships were applied to develop the proposed evolution simulation model in which the cutting force is adjusted to improve the required surface quality for the end-milling process. The results provide a means for greater efficiency by improving the surface quality, minimizing the effect of the process variability and reducing the error cost during finishing operations.   },
	issn = {0039-2480},	pages = {524-540},	doi = {},
	url = {https://www.sv-jme.eu/article/a-model-based-system-for-the-dynamic-adjustment-of-cutting-parameters-during-a-milling-process/}
}
Čuš, F.,Župerl, U.,Kiker, E.
2007 August 53. A model-based system for the dynamic adjustment of cutting parameters during a milling process. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 53:9
%A Čuš, Franci 
%A Župerl, Uroš 
%A Kiker, Edvard 
%D 2007
%T A model-based system for the dynamic adjustment of cutting parameters during a milling process
%B 2007
%9 end-milling; cutting parameters; genetic programming; model-based control; 
%! A model-based system for the dynamic adjustment of cutting parameters during a milling process
%K end-milling; cutting parameters; genetic programming; model-based control; 
%X This paper presents a model-based mechanism of control ensuring the constant quality of the surface finish by controlling the cutting forces during the end-milling process. Using the dynamic adaptation of feeding and speed the system controls the surface roughness and the cutting forces on the milling cutter The purpose of developing such a mechanism is to find the limitations of this type of control, which maintains a constant cutting force by adapting the cutting parameters. This model-based system of control was developed by the evolutionary method of genetic programming (GP). A drawing of experiments was made in order to determine the empirical correlations between the quality of the surface finish and the cutting force. With the depth of cutting defined in advance the influence of the workpiece material and cutting parameters (feeding, cutting depth) on the above mentioned correlation has been experimentally researched. The evolution genetic programming method (GP) was applied to derive an empirical relationship for the surface finish and the cutting force values for steel materials. These relationships were applied to develop the proposed evolution simulation model in which the cutting force is adjusted to improve the required surface quality for the end-milling process. The results provide a means for greater efficiency by improving the surface quality, minimizing the effect of the process variability and reducing the error cost during finishing operations.   
%U https://www.sv-jme.eu/article/a-model-based-system-for-the-dynamic-adjustment-of-cutting-parameters-during-a-milling-process/
%0 Journal Article
%R 
%& 524
%P 17
%J Strojniški vestnik - Journal of Mechanical Engineering
%V 53
%N 9
%@ 0039-2480
%8 2017-08-18
%7 2017-08-18
Čuš, Franci, Uroš  Župerl, & Edvard  Kiker.
"A model-based system for the dynamic adjustment of cutting parameters during a milling process." Strojniški vestnik - Journal of Mechanical Engineering [Online], 53.9 (2007): 524-540. Web.  04 Jul. 2022
TY  - JOUR
AU  - Čuš, Franci 
AU  - Župerl, Uroš 
AU  - Kiker, Edvard 
PY  - 2007
TI  - A model-based system for the dynamic adjustment of cutting parameters during a milling process
JF  - Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - end-milling; cutting parameters; genetic programming; model-based control; 
N2  - This paper presents a model-based mechanism of control ensuring the constant quality of the surface finish by controlling the cutting forces during the end-milling process. Using the dynamic adaptation of feeding and speed the system controls the surface roughness and the cutting forces on the milling cutter The purpose of developing such a mechanism is to find the limitations of this type of control, which maintains a constant cutting force by adapting the cutting parameters. This model-based system of control was developed by the evolutionary method of genetic programming (GP). A drawing of experiments was made in order to determine the empirical correlations between the quality of the surface finish and the cutting force. With the depth of cutting defined in advance the influence of the workpiece material and cutting parameters (feeding, cutting depth) on the above mentioned correlation has been experimentally researched. The evolution genetic programming method (GP) was applied to derive an empirical relationship for the surface finish and the cutting force values for steel materials. These relationships were applied to develop the proposed evolution simulation model in which the cutting force is adjusted to improve the required surface quality for the end-milling process. The results provide a means for greater efficiency by improving the surface quality, minimizing the effect of the process variability and reducing the error cost during finishing operations.   
UR  - https://www.sv-jme.eu/article/a-model-based-system-for-the-dynamic-adjustment-of-cutting-parameters-during-a-milling-process/
@article{{}{.},
	author = {Čuš, F., Župerl, U., Kiker, E.},
	title = {A model-based system for the dynamic adjustment of cutting parameters during a milling process},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {53},
	number = {9},
	year = {2007},
	doi = {},
	url = {https://www.sv-jme.eu/article/a-model-based-system-for-the-dynamic-adjustment-of-cutting-parameters-during-a-milling-process/}
}
TY  - JOUR
AU  - Čuš, Franci 
AU  - Župerl, Uroš 
AU  - Kiker, Edvard 
PY  - 2017/08/18
TI  - A model-based system for the dynamic adjustment of cutting parameters during a milling process
JF  - Strojniški vestnik - Journal of Mechanical Engineering; Vol 53, No 9 (2007): Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - end-milling, cutting parameters, genetic programming, model-based control, 
N2  - This paper presents a model-based mechanism of control ensuring the constant quality of the surface finish by controlling the cutting forces during the end-milling process. Using the dynamic adaptation of feeding and speed the system controls the surface roughness and the cutting forces on the milling cutter The purpose of developing such a mechanism is to find the limitations of this type of control, which maintains a constant cutting force by adapting the cutting parameters. This model-based system of control was developed by the evolutionary method of genetic programming (GP). A drawing of experiments was made in order to determine the empirical correlations between the quality of the surface finish and the cutting force. With the depth of cutting defined in advance the influence of the workpiece material and cutting parameters (feeding, cutting depth) on the above mentioned correlation has been experimentally researched. The evolution genetic programming method (GP) was applied to derive an empirical relationship for the surface finish and the cutting force values for steel materials. These relationships were applied to develop the proposed evolution simulation model in which the cutting force is adjusted to improve the required surface quality for the end-milling process. The results provide a means for greater efficiency by improving the surface quality, minimizing the effect of the process variability and reducing the error cost during finishing operations.   
UR  - https://www.sv-jme.eu/article/a-model-based-system-for-the-dynamic-adjustment-of-cutting-parameters-during-a-milling-process/
Čuš, Franci, Župerl, Uroš, AND Kiker, Edvard.
"A model-based system for the dynamic adjustment of cutting parameters during a milling process" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 53 Number 9 (18 August 2017)

Authors

Affiliations

  • University of Maribor, Faculty of Mechanical Engineering, Slovenia
  • University of Maribor, Faculty of Mechanical Engineering, Slovenia
  • University of Maribor, Faculty of Mechanical Engineering, Slovenia

Paper's information

Strojniški vestnik - Journal of Mechanical Engineering 53(2007)9, 524-540
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.

This paper presents a model-based mechanism of control ensuring the constant quality of the surface finish by controlling the cutting forces during the end-milling process. Using the dynamic adaptation of feeding and speed the system controls the surface roughness and the cutting forces on the milling cutter The purpose of developing such a mechanism is to find the limitations of this type of control, which maintains a constant cutting force by adapting the cutting parameters. This model-based system of control was developed by the evolutionary method of genetic programming (GP). A drawing of experiments was made in order to determine the empirical correlations between the quality of the surface finish and the cutting force. With the depth of cutting defined in advance the influence of the workpiece material and cutting parameters (feeding, cutting depth) on the above mentioned correlation has been experimentally researched. The evolution genetic programming method (GP) was applied to derive an empirical relationship for the surface finish and the cutting force values for steel materials. These relationships were applied to develop the proposed evolution simulation model in which the cutting force is adjusted to improve the required surface quality for the end-milling process. The results provide a means for greater efficiency by improving the surface quality, minimizing the effect of the process variability and reducing the error cost during finishing operations.   

end-milling; cutting parameters; genetic programming; model-based control;