Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process

1471 Views
1048 Downloads
Export citation: ABNT
ZGÓRNIAK, Piotr ;STACHURSKI, Wojciech ;OSTROWSKI, Dariusz .
Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process. 
Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 62, n.11, p. 657-664, june 2018. 
ISSN 0039-2480.
Available at: <https://www.sv-jme.eu/article/application-of-thermographic-measurements-for-the-determination-of-the-impact-of-selected-cutting-parameters-on-the-temperature-in-the-workpiece-during-milling-process/>. Date accessed: 05 dec. 2021. 
doi:http://dx.doi.org/10.5545/sv-jme.2015.3259.
Zgórniak, P., Stachurski, W., & Ostrowski, D.
(2016).
Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process.
Strojniški vestnik - Journal of Mechanical Engineering, 62(11), 657-664.
doi:http://dx.doi.org/10.5545/sv-jme.2015.3259
@article{sv-jmesv-jme.2015.3259,
	author = {Piotr  Zgórniak and Wojciech  Stachurski and Dariusz  Ostrowski},
	title = {Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {62},
	number = {11},
	year = {2016},
	keywords = {machining, IR measurements, workpiece temperature},
	abstract = {In this paper, the impact of selected cutting parameters (both cutting and feed speed) on the temperature generated in the workpiece being machined during milling is assessed. The investigations were carried out by milling of 41Cr4 alloy steel using disc cutter mill with F40M sintered carbide inserts with the anti-wear coating. The investigations were conducted with the dry cutting manner. During the investigations three cutting speeds and three feed speeds were applied, with a constant depth of cut. In the course of the investigations, the temperature in the machining, the zone was recorded using the Flir SC6000HS infrared camera. As a result of the measurements, the mean temperature in the defined measurement zone was determined, and, based on that, a procedure for the determination of the tW-max maximum temperature in the workpiece being machined has been proposed. Finally, on the basis of the obtained results, it has been found that the increase in cutting speed leads to the increase in the tW-max maximum temperature, whereas the increase in feed speed leads to the reduction of that temperature in the workpiece being machined.},
	issn = {0039-2480},	pages = {657-664},	doi = {10.5545/sv-jme.2015.3259},
	url = {https://www.sv-jme.eu/article/application-of-thermographic-measurements-for-the-determination-of-the-impact-of-selected-cutting-parameters-on-the-temperature-in-the-workpiece-during-milling-process/}
}
Zgórniak, P.,Stachurski, W.,Ostrowski, D.
2016 June 62. Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 62:11
%A Zgórniak, Piotr 
%A Stachurski, Wojciech 
%A Ostrowski, Dariusz 
%D 2016
%T Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process
%B 2016
%9 machining, IR measurements, workpiece temperature
%! Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process
%K machining, IR measurements, workpiece temperature
%X In this paper, the impact of selected cutting parameters (both cutting and feed speed) on the temperature generated in the workpiece being machined during milling is assessed. The investigations were carried out by milling of 41Cr4 alloy steel using disc cutter mill with F40M sintered carbide inserts with the anti-wear coating. The investigations were conducted with the dry cutting manner. During the investigations three cutting speeds and three feed speeds were applied, with a constant depth of cut. In the course of the investigations, the temperature in the machining, the zone was recorded using the Flir SC6000HS infrared camera. As a result of the measurements, the mean temperature in the defined measurement zone was determined, and, based on that, a procedure for the determination of the tW-max maximum temperature in the workpiece being machined has been proposed. Finally, on the basis of the obtained results, it has been found that the increase in cutting speed leads to the increase in the tW-max maximum temperature, whereas the increase in feed speed leads to the reduction of that temperature in the workpiece being machined.
%U https://www.sv-jme.eu/article/application-of-thermographic-measurements-for-the-determination-of-the-impact-of-selected-cutting-parameters-on-the-temperature-in-the-workpiece-during-milling-process/
%0 Journal Article
%R 10.5545/sv-jme.2015.3259
%& 657
%P 8
%J Strojniški vestnik - Journal of Mechanical Engineering
%V 62
%N 11
%@ 0039-2480
%8 2018-06-27
%7 2018-06-27
Zgórniak, Piotr, Wojciech  Stachurski, & Dariusz  Ostrowski.
"Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process." Strojniški vestnik - Journal of Mechanical Engineering [Online], 62.11 (2016): 657-664. Web.  05 Dec. 2021
TY  - JOUR
AU  - Zgórniak, Piotr 
AU  - Stachurski, Wojciech 
AU  - Ostrowski, Dariusz 
PY  - 2016
TI  - Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process
JF  - Strojniški vestnik - Journal of Mechanical Engineering
DO  - 10.5545/sv-jme.2015.3259
KW  - machining, IR measurements, workpiece temperature
N2  - In this paper, the impact of selected cutting parameters (both cutting and feed speed) on the temperature generated in the workpiece being machined during milling is assessed. The investigations were carried out by milling of 41Cr4 alloy steel using disc cutter mill with F40M sintered carbide inserts with the anti-wear coating. The investigations were conducted with the dry cutting manner. During the investigations three cutting speeds and three feed speeds were applied, with a constant depth of cut. In the course of the investigations, the temperature in the machining, the zone was recorded using the Flir SC6000HS infrared camera. As a result of the measurements, the mean temperature in the defined measurement zone was determined, and, based on that, a procedure for the determination of the tW-max maximum temperature in the workpiece being machined has been proposed. Finally, on the basis of the obtained results, it has been found that the increase in cutting speed leads to the increase in the tW-max maximum temperature, whereas the increase in feed speed leads to the reduction of that temperature in the workpiece being machined.
UR  - https://www.sv-jme.eu/article/application-of-thermographic-measurements-for-the-determination-of-the-impact-of-selected-cutting-parameters-on-the-temperature-in-the-workpiece-during-milling-process/
@article{{sv-jme}{sv-jme.2015.3259},
	author = {Zgórniak, P., Stachurski, W., Ostrowski, D.},
	title = {Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {62},
	number = {11},
	year = {2016},
	doi = {10.5545/sv-jme.2015.3259},
	url = {https://www.sv-jme.eu/article/application-of-thermographic-measurements-for-the-determination-of-the-impact-of-selected-cutting-parameters-on-the-temperature-in-the-workpiece-during-milling-process/}
}
TY  - JOUR
AU  - Zgórniak, Piotr 
AU  - Stachurski, Wojciech 
AU  - Ostrowski, Dariusz 
PY  - 2018/06/27
TI  - Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process
JF  - Strojniški vestnik - Journal of Mechanical Engineering; Vol 62, No 11 (2016): Strojniški vestnik - Journal of Mechanical Engineering
DO  - 10.5545/sv-jme.2015.3259
KW  - machining, IR measurements, workpiece temperature
N2  - In this paper, the impact of selected cutting parameters (both cutting and feed speed) on the temperature generated in the workpiece being machined during milling is assessed. The investigations were carried out by milling of 41Cr4 alloy steel using disc cutter mill with F40M sintered carbide inserts with the anti-wear coating. The investigations were conducted with the dry cutting manner. During the investigations three cutting speeds and three feed speeds were applied, with a constant depth of cut. In the course of the investigations, the temperature in the machining, the zone was recorded using the Flir SC6000HS infrared camera. As a result of the measurements, the mean temperature in the defined measurement zone was determined, and, based on that, a procedure for the determination of the tW-max maximum temperature in the workpiece being machined has been proposed. Finally, on the basis of the obtained results, it has been found that the increase in cutting speed leads to the increase in the tW-max maximum temperature, whereas the increase in feed speed leads to the reduction of that temperature in the workpiece being machined.
UR  - https://www.sv-jme.eu/article/application-of-thermographic-measurements-for-the-determination-of-the-impact-of-selected-cutting-parameters-on-the-temperature-in-the-workpiece-during-milling-process/
Zgórniak, Piotr, Stachurski, Wojciech, AND Ostrowski, Dariusz.
"Application of Thermographic Measurements for the Determination of the Impact of Selected Cutting Parameters on the Temperature in the Workpiece During Milling Process" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 62 Number 11 (27 June 2018)

Authors

Affiliations

  • Lodz University of Technology, Institute of Machine Tools and Production Engineering, Poland 1

Paper's information

Strojniški vestnik - Journal of Mechanical Engineering 62(2016)11, 657-664

https://doi.org/10.5545/sv-jme.2015.3259

In this paper, the impact of selected cutting parameters (both cutting and feed speed) on the temperature generated in the workpiece being machined during milling is assessed. The investigations were carried out by milling of 41Cr4 alloy steel using disc cutter mill with F40M sintered carbide inserts with the anti-wear coating. The investigations were conducted with the dry cutting manner. During the investigations three cutting speeds and three feed speeds were applied, with a constant depth of cut. In the course of the investigations, the temperature in the machining, the zone was recorded using the Flir SC6000HS infrared camera. As a result of the measurements, the mean temperature in the defined measurement zone was determined, and, based on that, a procedure for the determination of the tW-max maximum temperature in the workpiece being machined has been proposed. Finally, on the basis of the obtained results, it has been found that the increase in cutting speed leads to the increase in the tW-max maximum temperature, whereas the increase in feed speed leads to the reduction of that temperature in the workpiece being machined.

machining, IR measurements, workpiece temperature