Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method

670 Views
370 Downloads
Export citation: ABNT
KORKUT, Ihsan ;KUCUK, Yilmaz .
Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method. 
Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 56, n.5, p. 340-346, october 2017. 
ISSN 0039-2480.
Available at: <https://www.sv-jme.eu/article/experimental-analysis-of-the-deviation-from-circularity-of-bored-hole-based-on-the-taguchi-method/>. Date accessed: 30 may. 2020. 
doi:http://dx.doi.org/.
Korkut, I., & Kucuk, Y.
(2010).
Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method.
Strojniški vestnik - Journal of Mechanical Engineering, 56(5), 340-346.
doi:http://dx.doi.org/
@article{.,
	author = {Ihsan  Korkut and Yilmaz  Kucuk},
	title = {Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {56},
	number = {5},
	year = {2010},
	keywords = {boring; machining; experimentation; optimization; Taguchi method; analyze; },
	abstract = {In this study, the effects of cutting parameters, boring tool material and the overhang ratio of boring tool (tool clamping length) on the deviation from circularity of a bored hole were examined experimentally. The optimal cutting condition can be estimated by the analysis of the signal to noise (S/N) ratio in Taguchi method. The individual contributions of each factor on the deviation from circularity were calculated by using the Analysis of Variance (ANOVA). Therefore, at the determined condition, it could be observed whether a factor is significant or not. Also, it was observed that the values of deviation from circularity increased significantly with an increase in the effective tool length at the lower depth of cut values. In addition, the circularity could be improved with increasing the depth of cut values for the same tool clamping lengths.},
	issn = {0039-2480},	pages = {340-346},	doi = {},
	url = {https://www.sv-jme.eu/article/experimental-analysis-of-the-deviation-from-circularity-of-bored-hole-based-on-the-taguchi-method/}
}
Korkut, I.,Kucuk, Y.
2010 October 56. Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 56:5
%A Korkut, Ihsan 
%A Kucuk, Yilmaz 
%D 2010
%T Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method
%B 2010
%9 boring; machining; experimentation; optimization; Taguchi method; analyze; 
%! Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method
%K boring; machining; experimentation; optimization; Taguchi method; analyze; 
%X In this study, the effects of cutting parameters, boring tool material and the overhang ratio of boring tool (tool clamping length) on the deviation from circularity of a bored hole were examined experimentally. The optimal cutting condition can be estimated by the analysis of the signal to noise (S/N) ratio in Taguchi method. The individual contributions of each factor on the deviation from circularity were calculated by using the Analysis of Variance (ANOVA). Therefore, at the determined condition, it could be observed whether a factor is significant or not. Also, it was observed that the values of deviation from circularity increased significantly with an increase in the effective tool length at the lower depth of cut values. In addition, the circularity could be improved with increasing the depth of cut values for the same tool clamping lengths.
%U https://www.sv-jme.eu/article/experimental-analysis-of-the-deviation-from-circularity-of-bored-hole-based-on-the-taguchi-method/
%0 Journal Article
%R 
%& 340
%P 7
%J Strojniški vestnik - Journal of Mechanical Engineering
%V 56
%N 5
%@ 0039-2480
%8 2017-10-24
%7 2017-10-24
Korkut, Ihsan, & Yilmaz  Kucuk.
"Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method." Strojniški vestnik - Journal of Mechanical Engineering [Online], 56.5 (2010): 340-346. Web.  30 May. 2020
TY  - JOUR
AU  - Korkut, Ihsan 
AU  - Kucuk, Yilmaz 
PY  - 2010
TI  - Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method
JF  - Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - boring; machining; experimentation; optimization; Taguchi method; analyze; 
N2  - In this study, the effects of cutting parameters, boring tool material and the overhang ratio of boring tool (tool clamping length) on the deviation from circularity of a bored hole were examined experimentally. The optimal cutting condition can be estimated by the analysis of the signal to noise (S/N) ratio in Taguchi method. The individual contributions of each factor on the deviation from circularity were calculated by using the Analysis of Variance (ANOVA). Therefore, at the determined condition, it could be observed whether a factor is significant or not. Also, it was observed that the values of deviation from circularity increased significantly with an increase in the effective tool length at the lower depth of cut values. In addition, the circularity could be improved with increasing the depth of cut values for the same tool clamping lengths.
UR  - https://www.sv-jme.eu/article/experimental-analysis-of-the-deviation-from-circularity-of-bored-hole-based-on-the-taguchi-method/
@article{{}{.},
	author = {Korkut, I., Kucuk, Y.},
	title = {Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {56},
	number = {5},
	year = {2010},
	doi = {},
	url = {https://www.sv-jme.eu/article/experimental-analysis-of-the-deviation-from-circularity-of-bored-hole-based-on-the-taguchi-method/}
}
TY  - JOUR
AU  - Korkut, Ihsan 
AU  - Kucuk, Yilmaz 
PY  - 2017/10/24
TI  - Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method
JF  - Strojniški vestnik - Journal of Mechanical Engineering; Vol 56, No 5 (2010): Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - boring, machining, experimentation, optimization, Taguchi method, analyze, 
N2  - In this study, the effects of cutting parameters, boring tool material and the overhang ratio of boring tool (tool clamping length) on the deviation from circularity of a bored hole were examined experimentally. The optimal cutting condition can be estimated by the analysis of the signal to noise (S/N) ratio in Taguchi method. The individual contributions of each factor on the deviation from circularity were calculated by using the Analysis of Variance (ANOVA). Therefore, at the determined condition, it could be observed whether a factor is significant or not. Also, it was observed that the values of deviation from circularity increased significantly with an increase in the effective tool length at the lower depth of cut values. In addition, the circularity could be improved with increasing the depth of cut values for the same tool clamping lengths.
UR  - https://www.sv-jme.eu/article/experimental-analysis-of-the-deviation-from-circularity-of-bored-hole-based-on-the-taguchi-method/
Korkut, Ihsan, AND Kucuk, Yilmaz.
"Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 56 Number 5 (24 October 2017)

Authors

Affiliations

  • Department of Mechanical Education, Faculty of Technology, Gazi University, Turkey
  • Department of Mechanical Engineering, Engineering Faculty, Bartin University, Turkey

Paper's information

Strojniški vestnik - Journal of Mechanical Engineering 56(2010)5, 340-346

In this study, the effects of cutting parameters, boring tool material and the overhang ratio of boring tool (tool clamping length) on the deviation from circularity of a bored hole were examined experimentally. The optimal cutting condition can be estimated by the analysis of the signal to noise (S/N) ratio in Taguchi method. The individual contributions of each factor on the deviation from circularity were calculated by using the Analysis of Variance (ANOVA). Therefore, at the determined condition, it could be observed whether a factor is significant or not. Also, it was observed that the values of deviation from circularity increased significantly with an increase in the effective tool length at the lower depth of cut values. In addition, the circularity could be improved with increasing the depth of cut values for the same tool clamping lengths.

boring; machining; experimentation; optimization; Taguchi method; analyze;