Occurance of Fretting in Modern Devices and Machinery

1694 Views
1014 Downloads
Export citation: ABNT
KALIN, Mitjan ;VIŽINTIN, Jože .
Occurance of Fretting in Modern Devices and Machinery. 
Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 45, n.5, p. 185-198, november 2017. 
ISSN 0039-2480.
Available at: <https://www.sv-jme.eu/article/occurance-of-fretting-in-modern-devices-and-machinery/>. Date accessed: 13 apr. 2024. 
doi:http://dx.doi.org/.
Kalin, M., & Vižintin, J.
(1999).
Occurance of Fretting in Modern Devices and Machinery.
Strojniški vestnik - Journal of Mechanical Engineering, 45(5), 185-198.
doi:http://dx.doi.org/
@article{.,
	author = {Mitjan  Kalin and Jože  Vižintin},
	title = {Occurance of Fretting in Modern Devices and Machinery},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {45},
	number = {5},
	year = {1999},
	keywords = {frretting; steel; ceramics; silicon nitride; },
	abstract = {Fretting conditions are found in practically any technical system where contact vibrations are present, or where the contact stresses are induced by cyclic accelerations, fatique stresses, acoustical noise or temperature variations, thus enabling small relative motion. It is known that even reciprocating movements as short as 0.1 mikrometra in amplitude can cause failure of e component. This means that fretting is very difficult to completely prevent. Recently, high performance ceramics are increasingly used in modern machinery. Consequently, more frequent occurrences of fretting between the ceramics and steel - the prevailing engineering material - are expected. The ceramic material which is used most frequently in applications where fretting could occur is silicon nitride, and therefore it deserves the most attention. In this paper, the most common application where fretting occurs between the steel and silicon nitride ceramics are presented.},
	issn = {0039-2480},	pages = {185-198},	doi = {},
	url = {https://www.sv-jme.eu/article/occurance-of-fretting-in-modern-devices-and-machinery/}
}
Kalin, M.,Vižintin, J.
1999 November 45. Occurance of Fretting in Modern Devices and Machinery. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 45:5
%A Kalin, Mitjan 
%A Vižintin, Jože 
%D 1999
%T Occurance of Fretting in Modern Devices and Machinery
%B 1999
%9 frretting; steel; ceramics; silicon nitride; 
%! Occurance of Fretting in Modern Devices and Machinery
%K frretting; steel; ceramics; silicon nitride; 
%X Fretting conditions are found in practically any technical system where contact vibrations are present, or where the contact stresses are induced by cyclic accelerations, fatique stresses, acoustical noise or temperature variations, thus enabling small relative motion. It is known that even reciprocating movements as short as 0.1 mikrometra in amplitude can cause failure of e component. This means that fretting is very difficult to completely prevent. Recently, high performance ceramics are increasingly used in modern machinery. Consequently, more frequent occurrences of fretting between the ceramics and steel - the prevailing engineering material - are expected. The ceramic material which is used most frequently in applications where fretting could occur is silicon nitride, and therefore it deserves the most attention. In this paper, the most common application where fretting occurs between the steel and silicon nitride ceramics are presented.
%U https://www.sv-jme.eu/article/occurance-of-fretting-in-modern-devices-and-machinery/
%0 Journal Article
%R 
%& 185
%P 14
%J Strojniški vestnik - Journal of Mechanical Engineering
%V 45
%N 5
%@ 0039-2480
%8 2017-11-11
%7 2017-11-11
Kalin, Mitjan, & Jože  Vižintin.
"Occurance of Fretting in Modern Devices and Machinery." Strojniški vestnik - Journal of Mechanical Engineering [Online], 45.5 (1999): 185-198. Web.  13 Apr. 2024
TY  - JOUR
AU  - Kalin, Mitjan 
AU  - Vižintin, Jože 
PY  - 1999
TI  - Occurance of Fretting in Modern Devices and Machinery
JF  - Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - frretting; steel; ceramics; silicon nitride; 
N2  - Fretting conditions are found in practically any technical system where contact vibrations are present, or where the contact stresses are induced by cyclic accelerations, fatique stresses, acoustical noise or temperature variations, thus enabling small relative motion. It is known that even reciprocating movements as short as 0.1 mikrometra in amplitude can cause failure of e component. This means that fretting is very difficult to completely prevent. Recently, high performance ceramics are increasingly used in modern machinery. Consequently, more frequent occurrences of fretting between the ceramics and steel - the prevailing engineering material - are expected. The ceramic material which is used most frequently in applications where fretting could occur is silicon nitride, and therefore it deserves the most attention. In this paper, the most common application where fretting occurs between the steel and silicon nitride ceramics are presented.
UR  - https://www.sv-jme.eu/article/occurance-of-fretting-in-modern-devices-and-machinery/
@article{{}{.},
	author = {Kalin, M., Vižintin, J.},
	title = {Occurance of Fretting in Modern Devices and Machinery},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {45},
	number = {5},
	year = {1999},
	doi = {},
	url = {https://www.sv-jme.eu/article/occurance-of-fretting-in-modern-devices-and-machinery/}
}
TY  - JOUR
AU  - Kalin, Mitjan 
AU  - Vižintin, Jože 
PY  - 2017/11/11
TI  - Occurance of Fretting in Modern Devices and Machinery
JF  - Strojniški vestnik - Journal of Mechanical Engineering; Vol 45, No 5 (1999): Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - frretting, steel, ceramics, silicon nitride, 
N2  - Fretting conditions are found in practically any technical system where contact vibrations are present, or where the contact stresses are induced by cyclic accelerations, fatique stresses, acoustical noise or temperature variations, thus enabling small relative motion. It is known that even reciprocating movements as short as 0.1 mikrometra in amplitude can cause failure of e component. This means that fretting is very difficult to completely prevent. Recently, high performance ceramics are increasingly used in modern machinery. Consequently, more frequent occurrences of fretting between the ceramics and steel - the prevailing engineering material - are expected. The ceramic material which is used most frequently in applications where fretting could occur is silicon nitride, and therefore it deserves the most attention. In this paper, the most common application where fretting occurs between the steel and silicon nitride ceramics are presented.
UR  - https://www.sv-jme.eu/article/occurance-of-fretting-in-modern-devices-and-machinery/
Kalin, Mitjan, AND Vižintin, Jože.
"Occurance of Fretting in Modern Devices and Machinery" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 45 Number 5 (11 November 2017)

Authors

Affiliations

  • University of Ljubljana, Faculty of Mechanical Engineering, Centre for Tribology and Technical Diagnostics, Ljubljana, Slovenia
  • University of Ljubljana, Faculty of Mechanical Engineering, Centre for Tribology and Technical Diagnostics, Ljubljana, Slovenia

Paper's information

Strojniški vestnik - Journal of Mechanical Engineering 45(1999)5, 185-198
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.

Fretting conditions are found in practically any technical system where contact vibrations are present, or where the contact stresses are induced by cyclic accelerations, fatique stresses, acoustical noise or temperature variations, thus enabling small relative motion. It is known that even reciprocating movements as short as 0.1 mikrometra in amplitude can cause failure of e component. This means that fretting is very difficult to completely prevent. Recently, high performance ceramics are increasingly used in modern machinery. Consequently, more frequent occurrences of fretting between the ceramics and steel - the prevailing engineering material - are expected. The ceramic material which is used most frequently in applications where fretting could occur is silicon nitride, and therefore it deserves the most attention. In this paper, the most common application where fretting occurs between the steel and silicon nitride ceramics are presented.

frretting; steel; ceramics; silicon nitride;