ÖZTÜRK, Ayşegül ;KAHVECI, Kamil . Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux. Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 62, n.9, p. 511-520, june 2018. ISSN 0039-2480. Available at: <https://www.sv-jme.eu/article/slip-flow-of-nanofluids-between-parallel-plates-heated-with-a-constant-heat-flux/>. Date accessed: 01 dec. 2024. doi:http://dx.doi.org/10.5545/sv-jme.2016.3188.
Öztürk, A., & Kahveci, K. (2016). Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux. Strojniški vestnik - Journal of Mechanical Engineering, 62(9), 511-520. doi:http://dx.doi.org/10.5545/sv-jme.2016.3188
@article{sv-jmesv-jme.2016.3188, author = {Ayşegül Öztürk and Kamil Kahveci}, title = {Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux}, journal = {Strojniški vestnik - Journal of Mechanical Engineering}, volume = {62}, number = {9}, year = {2016}, keywords = {slip flow; nanofluid; parallel plate; slip factor, Nusselt number}, abstract = {This study investigates the steady fully developed laminar flow and heat transfer of nanofluids between parallel plates heated with a constant heat flux. The governing equations were solved analytically under the boundary conditions of slip velocity and temperature jump. Water was taken as the base fluid and Cu, CuO and Al2O3 as the nanoparticles. The results were obtained for the slip factor in the range of 0 to 0.04, for the Brinkman number in the range of –0.1 to 0.1, for three different values of the ratio of the liquid layering thickness to the particle radius (0.1, 0.2, and 0.4) and for the solid volume fraction ranging from 0 % to 8 %. The results show that the nanoparticle presence in the base fluid has a significant effect on both the velocity field and heat-transfer characteristics. The average Nusselt number increases considerably with the increase of the nanoparticle solid volume fraction. The average Nusselt number takes much higher values for high values of the ratio of the liquid layering thickness to the nanoparticle radius. The average heat transfer rate of nanofluids between parallel plates ranges from the highest to the lowest when Cu, Al2O3, and CuO are used as nanoparticles, respectively.}, issn = {0039-2480}, pages = {511-520}, doi = {10.5545/sv-jme.2016.3188}, url = {https://www.sv-jme.eu/article/slip-flow-of-nanofluids-between-parallel-plates-heated-with-a-constant-heat-flux/} }
Öztürk, A.,Kahveci, K. 2016 June 62. Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 62:9
%A Öztürk, Ayşegül %A Kahveci, Kamil %D 2016 %T Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux %B 2016 %9 slip flow; nanofluid; parallel plate; slip factor, Nusselt number %! Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux %K slip flow; nanofluid; parallel plate; slip factor, Nusselt number %X This study investigates the steady fully developed laminar flow and heat transfer of nanofluids between parallel plates heated with a constant heat flux. The governing equations were solved analytically under the boundary conditions of slip velocity and temperature jump. Water was taken as the base fluid and Cu, CuO and Al2O3 as the nanoparticles. The results were obtained for the slip factor in the range of 0 to 0.04, for the Brinkman number in the range of –0.1 to 0.1, for three different values of the ratio of the liquid layering thickness to the particle radius (0.1, 0.2, and 0.4) and for the solid volume fraction ranging from 0 % to 8 %. The results show that the nanoparticle presence in the base fluid has a significant effect on both the velocity field and heat-transfer characteristics. The average Nusselt number increases considerably with the increase of the nanoparticle solid volume fraction. The average Nusselt number takes much higher values for high values of the ratio of the liquid layering thickness to the nanoparticle radius. The average heat transfer rate of nanofluids between parallel plates ranges from the highest to the lowest when Cu, Al2O3, and CuO are used as nanoparticles, respectively. %U https://www.sv-jme.eu/article/slip-flow-of-nanofluids-between-parallel-plates-heated-with-a-constant-heat-flux/ %0 Journal Article %R 10.5545/sv-jme.2016.3188 %& 511 %P 10 %J Strojniški vestnik - Journal of Mechanical Engineering %V 62 %N 9 %@ 0039-2480 %8 2018-06-27 %7 2018-06-27
Öztürk, Ayşegül, & Kamil Kahveci. "Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux." Strojniški vestnik - Journal of Mechanical Engineering [Online], 62.9 (2016): 511-520. Web. 01 Dec. 2024
TY - JOUR AU - Öztürk, Ayşegül AU - Kahveci, Kamil PY - 2016 TI - Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux JF - Strojniški vestnik - Journal of Mechanical Engineering DO - 10.5545/sv-jme.2016.3188 KW - slip flow; nanofluid; parallel plate; slip factor, Nusselt number N2 - This study investigates the steady fully developed laminar flow and heat transfer of nanofluids between parallel plates heated with a constant heat flux. The governing equations were solved analytically under the boundary conditions of slip velocity and temperature jump. Water was taken as the base fluid and Cu, CuO and Al2O3 as the nanoparticles. The results were obtained for the slip factor in the range of 0 to 0.04, for the Brinkman number in the range of –0.1 to 0.1, for three different values of the ratio of the liquid layering thickness to the particle radius (0.1, 0.2, and 0.4) and for the solid volume fraction ranging from 0 % to 8 %. The results show that the nanoparticle presence in the base fluid has a significant effect on both the velocity field and heat-transfer characteristics. The average Nusselt number increases considerably with the increase of the nanoparticle solid volume fraction. The average Nusselt number takes much higher values for high values of the ratio of the liquid layering thickness to the nanoparticle radius. The average heat transfer rate of nanofluids between parallel plates ranges from the highest to the lowest when Cu, Al2O3, and CuO are used as nanoparticles, respectively. UR - https://www.sv-jme.eu/article/slip-flow-of-nanofluids-between-parallel-plates-heated-with-a-constant-heat-flux/
@article{{sv-jme}{sv-jme.2016.3188}, author = {Öztürk, A., Kahveci, K.}, title = {Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux}, journal = {Strojniški vestnik - Journal of Mechanical Engineering}, volume = {62}, number = {9}, year = {2016}, doi = {10.5545/sv-jme.2016.3188}, url = {https://www.sv-jme.eu/article/slip-flow-of-nanofluids-between-parallel-plates-heated-with-a-constant-heat-flux/} }
TY - JOUR AU - Öztürk, Ayşegül AU - Kahveci, Kamil PY - 2018/06/27 TI - Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux JF - Strojniški vestnik - Journal of Mechanical Engineering; Vol 62, No 9 (2016): Strojniški vestnik - Journal of Mechanical Engineering DO - 10.5545/sv-jme.2016.3188 KW - slip flow, nanofluid, parallel plate, slip factor, Nusselt number N2 - This study investigates the steady fully developed laminar flow and heat transfer of nanofluids between parallel plates heated with a constant heat flux. The governing equations were solved analytically under the boundary conditions of slip velocity and temperature jump. Water was taken as the base fluid and Cu, CuO and Al2O3 as the nanoparticles. The results were obtained for the slip factor in the range of 0 to 0.04, for the Brinkman number in the range of –0.1 to 0.1, for three different values of the ratio of the liquid layering thickness to the particle radius (0.1, 0.2, and 0.4) and for the solid volume fraction ranging from 0 % to 8 %. The results show that the nanoparticle presence in the base fluid has a significant effect on both the velocity field and heat-transfer characteristics. The average Nusselt number increases considerably with the increase of the nanoparticle solid volume fraction. The average Nusselt number takes much higher values for high values of the ratio of the liquid layering thickness to the nanoparticle radius. The average heat transfer rate of nanofluids between parallel plates ranges from the highest to the lowest when Cu, Al2O3, and CuO are used as nanoparticles, respectively. UR - https://www.sv-jme.eu/article/slip-flow-of-nanofluids-between-parallel-plates-heated-with-a-constant-heat-flux/
Öztürk, Ayşegül, AND Kahveci, Kamil. "Slip Flow of Nanofluids between Parallel Plates Heated with a Constant Heat Flux" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 62 Number 9 (27 June 2018)
Strojniški vestnik - Journal of Mechanical Engineering 62(2016)9, 511-520
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.
This study investigates the steady fully developed laminar flow and heat transfer of nanofluids between parallel plates heated with a constant heat flux. The governing equations were solved analytically under the boundary conditions of slip velocity and temperature jump. Water was taken as the base fluid and Cu, CuO and Al2O3 as the nanoparticles. The results were obtained for the slip factor in the range of 0 to 0.04, for the Brinkman number in the range of –0.1 to 0.1, for three different values of the ratio of the liquid layering thickness to the particle radius (0.1, 0.2, and 0.4) and for the solid volume fraction ranging from 0 % to 8 %. The results show that the nanoparticle presence in the base fluid has a significant effect on both the velocity field and heat-transfer characteristics. The average Nusselt number increases considerably with the increase of the nanoparticle solid volume fraction. The average Nusselt number takes much higher values for high values of the ratio of the liquid layering thickness to the nanoparticle radius. The average heat transfer rate of nanofluids between parallel plates ranges from the highest to the lowest when Cu, Al2O3, and CuO are used as nanoparticles, respectively.