The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy

1932 Views
4644 Downloads
Export citation: ABNT
GÖKKAYA, Hasan .
The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy. 
Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 56, n.9, p. 584-593, october 2017. 
ISSN 0039-2480.
Available at: <https://www.sv-jme.eu/article/the-effects-of-machining-parameters-on-cutting-forces-surface-roughness-built-up-edge-bue-and-built-up-layer-bul-during-machining-aa2014-t4-alloy/>. Date accessed: 08 oct. 2024. 
doi:http://dx.doi.org/.
Gökkaya, H.
(2010).
The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy.
Strojniški vestnik - Journal of Mechanical Engineering, 56(9), 584-593.
doi:http://dx.doi.org/
@article{.,
	author = {Hasan  Gökkaya},
	title = {The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {56},
	number = {9},
	year = {2010},
	keywords = {AA2014 alloy; built-up edge (BUE); built-up layer (BUL); cutting force; surface roughness; machining; },
	abstract = {Tool wear, formed in cutting tool during machining processes, affects the surface roughness of the work piece, cutting forces and other output parameters. The effects of the machining parameters cutting speed (Vc) and the feed rate (f) on built-up edge (BUE), built-up layer (BUL), main cutting force (Fc), and surface roughness (Ra) is investigated in this study. The effects of the cutting parameters on cutting force and surface roughness has been examined by the use of Variance Analysis (ANOVA); and their optimum and critical cutting parameters were determined accordingly. AA2014 aluminum alloy was machined with uncoated carbide tools using Computer Numerical Control (CNC) turning machine under dry cutting conditions. Four different cutting speeds (200 m/min, 300 m/min, 400 m/min, and 500 m/min), five different feed rates (0.10 mm/rev, 0.15 mm/rev, 0.20 mm/rev, 0.25 mm/rev, and 0.30 mm/rev) and a constant depth of cut were selected as the machining parameters. BUE and BUL in the cutting tool were formed most at cutting speed 200 m/min and feed rate 0.30 mm/rev. The lowest cutting force was determined as 137 N at cutting speed 500 m/min and feed rate 0.10 mm/rev. The lowest average surface roughness, however, was determined as 0.93 µm at 500 m/min cutting speed and feed rate 0.10 mm/rev.},
	issn = {0039-2480},	pages = {584-593},	doi = {},
	url = {https://www.sv-jme.eu/article/the-effects-of-machining-parameters-on-cutting-forces-surface-roughness-built-up-edge-bue-and-built-up-layer-bul-during-machining-aa2014-t4-alloy/}
}
Gökkaya, H.
2010 October 56. The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 56:9
%A Gökkaya, Hasan 
%D 2010
%T The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy
%B 2010
%9 AA2014 alloy; built-up edge (BUE); built-up layer (BUL); cutting force; surface roughness; machining; 
%! The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy
%K AA2014 alloy; built-up edge (BUE); built-up layer (BUL); cutting force; surface roughness; machining; 
%X Tool wear, formed in cutting tool during machining processes, affects the surface roughness of the work piece, cutting forces and other output parameters. The effects of the machining parameters cutting speed (Vc) and the feed rate (f) on built-up edge (BUE), built-up layer (BUL), main cutting force (Fc), and surface roughness (Ra) is investigated in this study. The effects of the cutting parameters on cutting force and surface roughness has been examined by the use of Variance Analysis (ANOVA); and their optimum and critical cutting parameters were determined accordingly. AA2014 aluminum alloy was machined with uncoated carbide tools using Computer Numerical Control (CNC) turning machine under dry cutting conditions. Four different cutting speeds (200 m/min, 300 m/min, 400 m/min, and 500 m/min), five different feed rates (0.10 mm/rev, 0.15 mm/rev, 0.20 mm/rev, 0.25 mm/rev, and 0.30 mm/rev) and a constant depth of cut were selected as the machining parameters. BUE and BUL in the cutting tool were formed most at cutting speed 200 m/min and feed rate 0.30 mm/rev. The lowest cutting force was determined as 137 N at cutting speed 500 m/min and feed rate 0.10 mm/rev. The lowest average surface roughness, however, was determined as 0.93 µm at 500 m/min cutting speed and feed rate 0.10 mm/rev.
%U https://www.sv-jme.eu/article/the-effects-of-machining-parameters-on-cutting-forces-surface-roughness-built-up-edge-bue-and-built-up-layer-bul-during-machining-aa2014-t4-alloy/
%0 Journal Article
%R 
%& 584
%P 10
%J Strojniški vestnik - Journal of Mechanical Engineering
%V 56
%N 9
%@ 0039-2480
%8 2017-10-24
%7 2017-10-24
Gökkaya, Hasan.
"The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy." Strojniški vestnik - Journal of Mechanical Engineering [Online], 56.9 (2010): 584-593. Web.  08 Oct. 2024
TY  - JOUR
AU  - Gökkaya, Hasan 
PY  - 2010
TI  - The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy
JF  - Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - AA2014 alloy; built-up edge (BUE); built-up layer (BUL); cutting force; surface roughness; machining; 
N2  - Tool wear, formed in cutting tool during machining processes, affects the surface roughness of the work piece, cutting forces and other output parameters. The effects of the machining parameters cutting speed (Vc) and the feed rate (f) on built-up edge (BUE), built-up layer (BUL), main cutting force (Fc), and surface roughness (Ra) is investigated in this study. The effects of the cutting parameters on cutting force and surface roughness has been examined by the use of Variance Analysis (ANOVA); and their optimum and critical cutting parameters were determined accordingly. AA2014 aluminum alloy was machined with uncoated carbide tools using Computer Numerical Control (CNC) turning machine under dry cutting conditions. Four different cutting speeds (200 m/min, 300 m/min, 400 m/min, and 500 m/min), five different feed rates (0.10 mm/rev, 0.15 mm/rev, 0.20 mm/rev, 0.25 mm/rev, and 0.30 mm/rev) and a constant depth of cut were selected as the machining parameters. BUE and BUL in the cutting tool were formed most at cutting speed 200 m/min and feed rate 0.30 mm/rev. The lowest cutting force was determined as 137 N at cutting speed 500 m/min and feed rate 0.10 mm/rev. The lowest average surface roughness, however, was determined as 0.93 µm at 500 m/min cutting speed and feed rate 0.10 mm/rev.
UR  - https://www.sv-jme.eu/article/the-effects-of-machining-parameters-on-cutting-forces-surface-roughness-built-up-edge-bue-and-built-up-layer-bul-during-machining-aa2014-t4-alloy/
@article{{}{.},
	author = {Gökkaya, H.},
	title = {The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {56},
	number = {9},
	year = {2010},
	doi = {},
	url = {https://www.sv-jme.eu/article/the-effects-of-machining-parameters-on-cutting-forces-surface-roughness-built-up-edge-bue-and-built-up-layer-bul-during-machining-aa2014-t4-alloy/}
}
TY  - JOUR
AU  - Gökkaya, Hasan 
PY  - 2017/10/24
TI  - The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy
JF  - Strojniški vestnik - Journal of Mechanical Engineering; Vol 56, No 9 (2010): Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - AA2014 alloy, built-up edge (BUE), built-up layer (BUL), cutting force, surface roughness, machining, 
N2  - Tool wear, formed in cutting tool during machining processes, affects the surface roughness of the work piece, cutting forces and other output parameters. The effects of the machining parameters cutting speed (Vc) and the feed rate (f) on built-up edge (BUE), built-up layer (BUL), main cutting force (Fc), and surface roughness (Ra) is investigated in this study. The effects of the cutting parameters on cutting force and surface roughness has been examined by the use of Variance Analysis (ANOVA); and their optimum and critical cutting parameters were determined accordingly. AA2014 aluminum alloy was machined with uncoated carbide tools using Computer Numerical Control (CNC) turning machine under dry cutting conditions. Four different cutting speeds (200 m/min, 300 m/min, 400 m/min, and 500 m/min), five different feed rates (0.10 mm/rev, 0.15 mm/rev, 0.20 mm/rev, 0.25 mm/rev, and 0.30 mm/rev) and a constant depth of cut were selected as the machining parameters. BUE and BUL in the cutting tool were formed most at cutting speed 200 m/min and feed rate 0.30 mm/rev. The lowest cutting force was determined as 137 N at cutting speed 500 m/min and feed rate 0.10 mm/rev. The lowest average surface roughness, however, was determined as 0.93 µm at 500 m/min cutting speed and feed rate 0.10 mm/rev.
UR  - https://www.sv-jme.eu/article/the-effects-of-machining-parameters-on-cutting-forces-surface-roughness-built-up-edge-bue-and-built-up-layer-bul-during-machining-aa2014-t4-alloy/
Gökkaya, Hasan"The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 56 Number 9 (24 October 2017)

Authors

Affiliations

  • Department of Mechanical Engineering, Karabuk University, Turkey

Paper's information

Strojniški vestnik - Journal of Mechanical Engineering 56(2010)9, 584-593
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.

Tool wear, formed in cutting tool during machining processes, affects the surface roughness of the work piece, cutting forces and other output parameters. The effects of the machining parameters cutting speed (Vc) and the feed rate (f) on built-up edge (BUE), built-up layer (BUL), main cutting force (Fc), and surface roughness (Ra) is investigated in this study. The effects of the cutting parameters on cutting force and surface roughness has been examined by the use of Variance Analysis (ANOVA); and their optimum and critical cutting parameters were determined accordingly. AA2014 aluminum alloy was machined with uncoated carbide tools using Computer Numerical Control (CNC) turning machine under dry cutting conditions. Four different cutting speeds (200 m/min, 300 m/min, 400 m/min, and 500 m/min), five different feed rates (0.10 mm/rev, 0.15 mm/rev, 0.20 mm/rev, 0.25 mm/rev, and 0.30 mm/rev) and a constant depth of cut were selected as the machining parameters. BUE and BUL in the cutting tool were formed most at cutting speed 200 m/min and feed rate 0.30 mm/rev. The lowest cutting force was determined as 137 N at cutting speed 500 m/min and feed rate 0.10 mm/rev. The lowest average surface roughness, however, was determined as 0.93 µm at 500 m/min cutting speed and feed rate 0.10 mm/rev.

AA2014 alloy; built-up edge (BUE); built-up layer (BUL); cutting force; surface roughness; machining;