Wear And Friction Properties Of Hard Coatings For Forming Tools

1198 Views
897 Downloads
Export citation: ABNT
PODGORNIK, Bojan ;HOGMARK, Sture ;SANDBERG, Odd .
Wear And Friction Properties Of Hard Coatings For Forming Tools. 
Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 50, n.3, p. 146-156, july 2017. 
ISSN 0039-2480.
Available at: <https://www.sv-jme.eu/article/wear-and-friction-properties-of-hard-coatings-for-forming-tools/>. Date accessed: 04 jul. 2022. 
doi:http://dx.doi.org/.
Podgornik, B., Hogmark, S., & Sandberg, O.
(2004).
Wear And Friction Properties Of Hard Coatings For Forming Tools.
Strojniški vestnik - Journal of Mechanical Engineering, 50(3), 146-156.
doi:http://dx.doi.org/
@article{.,
	author = {Bojan  Podgornik and Sture  Hogmark and Odd  Sandberg},
	title = {Wear And Friction Properties Of Hard Coatings For Forming Tools},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {50},
	number = {3},
	year = {2004},
	keywords = {cold forming; hard coatings; adhesion; wear; friction; },
	abstract = {The aim of this paper was to investigate the potential of using hard physical vapour deposition (PVD) coatings on forming tools. A tribological evaluation of TiN, TiB2 , TaC and diamond like coating (DLC) coatings deposited on cold-worked tool steel was carried out in a load-scanning test rig and compared to the behaviour of different uncoated forming tool steels. The special test configuration, where austenitic stainless steel was used as the counter-material, makes it possible to gradually increase the normal load during forward sliding strokes, and to correspondingly decrease the load during reversed ones. In this investigation, the load range was 100 to 1300 N (contact pressure from 1 to 5 GPa). The experimental results indicate that the introduction of an appropriate hard coating will lead to an improved wear resistance and a longer lifetime for the forming tool. Furthermore, by using hard lowfriction coatings excellent anti-sticking properties can be obtained.},
	issn = {0039-2480},	pages = {146-156},	doi = {},
	url = {https://www.sv-jme.eu/article/wear-and-friction-properties-of-hard-coatings-for-forming-tools/}
}
Podgornik, B.,Hogmark, S.,Sandberg, O.
2004 July 50. Wear And Friction Properties Of Hard Coatings For Forming Tools. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 50:3
%A Podgornik, Bojan 
%A Hogmark, Sture 
%A Sandberg, Odd 
%D 2004
%T Wear And Friction Properties Of Hard Coatings For Forming Tools
%B 2004
%9 cold forming; hard coatings; adhesion; wear; friction; 
%! Wear And Friction Properties Of Hard Coatings For Forming Tools
%K cold forming; hard coatings; adhesion; wear; friction; 
%X The aim of this paper was to investigate the potential of using hard physical vapour deposition (PVD) coatings on forming tools. A tribological evaluation of TiN, TiB2 , TaC and diamond like coating (DLC) coatings deposited on cold-worked tool steel was carried out in a load-scanning test rig and compared to the behaviour of different uncoated forming tool steels. The special test configuration, where austenitic stainless steel was used as the counter-material, makes it possible to gradually increase the normal load during forward sliding strokes, and to correspondingly decrease the load during reversed ones. In this investigation, the load range was 100 to 1300 N (contact pressure from 1 to 5 GPa). The experimental results indicate that the introduction of an appropriate hard coating will lead to an improved wear resistance and a longer lifetime for the forming tool. Furthermore, by using hard lowfriction coatings excellent anti-sticking properties can be obtained.
%U https://www.sv-jme.eu/article/wear-and-friction-properties-of-hard-coatings-for-forming-tools/
%0 Journal Article
%R 
%& 146
%P 11
%J Strojniški vestnik - Journal of Mechanical Engineering
%V 50
%N 3
%@ 0039-2480
%8 2017-07-07
%7 2017-07-07
Podgornik, Bojan, Sture  Hogmark, & Odd  Sandberg.
"Wear And Friction Properties Of Hard Coatings For Forming Tools." Strojniški vestnik - Journal of Mechanical Engineering [Online], 50.3 (2004): 146-156. Web.  04 Jul. 2022
TY  - JOUR
AU  - Podgornik, Bojan 
AU  - Hogmark, Sture 
AU  - Sandberg, Odd 
PY  - 2004
TI  - Wear And Friction Properties Of Hard Coatings For Forming Tools
JF  - Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - cold forming; hard coatings; adhesion; wear; friction; 
N2  - The aim of this paper was to investigate the potential of using hard physical vapour deposition (PVD) coatings on forming tools. A tribological evaluation of TiN, TiB2 , TaC and diamond like coating (DLC) coatings deposited on cold-worked tool steel was carried out in a load-scanning test rig and compared to the behaviour of different uncoated forming tool steels. The special test configuration, where austenitic stainless steel was used as the counter-material, makes it possible to gradually increase the normal load during forward sliding strokes, and to correspondingly decrease the load during reversed ones. In this investigation, the load range was 100 to 1300 N (contact pressure from 1 to 5 GPa). The experimental results indicate that the introduction of an appropriate hard coating will lead to an improved wear resistance and a longer lifetime for the forming tool. Furthermore, by using hard lowfriction coatings excellent anti-sticking properties can be obtained.
UR  - https://www.sv-jme.eu/article/wear-and-friction-properties-of-hard-coatings-for-forming-tools/
@article{{}{.},
	author = {Podgornik, B., Hogmark, S., Sandberg, O.},
	title = {Wear And Friction Properties Of Hard Coatings For Forming Tools},
	journal = {Strojniški vestnik - Journal of Mechanical Engineering},
	volume = {50},
	number = {3},
	year = {2004},
	doi = {},
	url = {https://www.sv-jme.eu/article/wear-and-friction-properties-of-hard-coatings-for-forming-tools/}
}
TY  - JOUR
AU  - Podgornik, Bojan 
AU  - Hogmark, Sture 
AU  - Sandberg, Odd 
PY  - 2017/07/07
TI  - Wear And Friction Properties Of Hard Coatings For Forming Tools
JF  - Strojniški vestnik - Journal of Mechanical Engineering; Vol 50, No 3 (2004): Strojniški vestnik - Journal of Mechanical Engineering
DO  - 
KW  - cold forming, hard coatings, adhesion, wear, friction, 
N2  - The aim of this paper was to investigate the potential of using hard physical vapour deposition (PVD) coatings on forming tools. A tribological evaluation of TiN, TiB2 , TaC and diamond like coating (DLC) coatings deposited on cold-worked tool steel was carried out in a load-scanning test rig and compared to the behaviour of different uncoated forming tool steels. The special test configuration, where austenitic stainless steel was used as the counter-material, makes it possible to gradually increase the normal load during forward sliding strokes, and to correspondingly decrease the load during reversed ones. In this investigation, the load range was 100 to 1300 N (contact pressure from 1 to 5 GPa). The experimental results indicate that the introduction of an appropriate hard coating will lead to an improved wear resistance and a longer lifetime for the forming tool. Furthermore, by using hard lowfriction coatings excellent anti-sticking properties can be obtained.
UR  - https://www.sv-jme.eu/article/wear-and-friction-properties-of-hard-coatings-for-forming-tools/
Podgornik, Bojan, Hogmark, Sture, AND Sandberg, Odd.
"Wear And Friction Properties Of Hard Coatings For Forming Tools" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 50 Number 3 (07 July 2017)

Authors

Affiliations

  • University of Ljubljana, Faculty of Mechanical Engineering, Slovenia
  • Uppsala University, The tribomaterial group, Sweden
  • Uddeholm Tooling AB, Sweden

Paper's information

Strojniški vestnik - Journal of Mechanical Engineering 50(2004)3, 146-156
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.

The aim of this paper was to investigate the potential of using hard physical vapour deposition (PVD) coatings on forming tools. A tribological evaluation of TiN, TiB2 , TaC and diamond like coating (DLC) coatings deposited on cold-worked tool steel was carried out in a load-scanning test rig and compared to the behaviour of different uncoated forming tool steels. The special test configuration, where austenitic stainless steel was used as the counter-material, makes it possible to gradually increase the normal load during forward sliding strokes, and to correspondingly decrease the load during reversed ones. In this investigation, the load range was 100 to 1300 N (contact pressure from 1 to 5 GPa). The experimental results indicate that the introduction of an appropriate hard coating will lead to an improved wear resistance and a longer lifetime for the forming tool. Furthermore, by using hard lowfriction coatings excellent anti-sticking properties can be obtained.

cold forming; hard coatings; adhesion; wear; friction;